I PURCHASED A 2001 EDDIE BAUER AND NEED HELP PROGRAAMING GARAGE DOOR OPENER NO MANUAL WITH VECHICLE

Me too! I purchased a 2005 Explorer Limited and need to know how to program the garage door opener. Any help would be appreciated!
Thanks.

This is a 03 Expy , might work for youProgrammingDo not program HomeLink with the vehicle parked in the garage.Note: Your vehicle may require the ignition switch to be turned to theACC position for programming and/or operation of the HomeLink. It isalso recommended that a new battery be placed in the hand-heldtransmitter of the device being programmed to HomeLink for quickertraining and accurate transmission of the radio-frequency signal.1. Press and hold the two outsidebuttons releasing only when the redlight begins to flash after 20seconds. Do not repeat step one toprogram additional hand-heldtransmitters to the remaining twoHomeLink buttons. This will erasepreviously programmed hand-heldtransmitter signals into HomeLink.2. Position the end of yourhand-held transmitter 2–8 cm (1–3 inches) away from the HomeLinkbutton you wish to program (located on your visor) while keeping thered light in view.1223. Simultaneously press and holdboth the HomeLink and hand-heldtransmitter button. Do not releasethe buttons until step 4 has beencompleted.Some entry gates and garage dooropeners may require you to replacestep 3 with procedures noted in the“Gate Operator and Canadian Programming” section for Canadianresidents.4. The red light will flash slowly and then rapidly. Release both buttonswhen the red light flashes rapidly. (The rapid flashing light indicatesacceptance of the hand-held transmitters’ radio frequency signals.)5. Press and hold the just-trained HomeLink button and observe the redlight. If the light is a constant red, programming is complete and yourdevice should activate when the HomeLink button is pressed andreleased. Note: To program the remaining two HomeLink buttons,begin with step 2 in the “Programming” section — do not repeat step 1.Note: If the red light blinks rapidly for two seconds and then turns to acontinuous red, proceed with steps 6 through 8 to completeprogramming of a rolling code equipped device.6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire is attached to the unit).7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.)Note: There are 30 seconds in which to initiate step eight.8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink button. Repeat the press/hold/release sequenceagain, and, depending on the brand of the garage door opener (or otherrolling code equipped device), repeat this sequence a third time tocomplete the programming.HomeLink should now activate your rolling code equipped device. Toprogram additional HomeLink buttons begin with step 2 in the“Programming” section. For questions or comments, please contactHomeLink at www.homelink.com or 1–800–355–3515.Driver Controls123Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink to accept the signalfrom the hand-held transmitter.After completing steps 1 and 2outlined in the “Programming”section, replace step 3 with the following:Note: If programming a garage door opener or gate operator, it isadvised to unplug the device during the “cycling” process to preventoverheating.• Continue to press and hold the HomeLink button (note step 3 in the“Programming” section) while you press and release — every twoseconds (“cycle”) your hand-held transmitter until the frequencysignal has been accepted by the HomeLink. The red indicator lightwill flash slowly and then rapidly after HomeLink accepts the radiofrequency signal.• Proceed with step 4 in the “Programming” section.Operating the HomeLink Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink button.Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmitter of the devicemay also be used at any time. In the event that there are stillprogramming difficulties, contact HomeLink at www.homelink.com or1–800–355–3515.